Cara memperbaiki "setup was unable to create a new system partition or locate an existing system partition" saat install windows

I received two computers, & they are both having identical problems. I am booting from USB và I see the hard drive, but I get this message "Setup was unable khổng lồ create a new system partition or locate an existing system partition. Searching this there were multiple people that had success with using the disk part utility. I ran the utility twice, on BOTH computers và I was still getting the same errors.

Bạn đang xem: Cara memperbaiki "setup was unable to create a new system partition or locate an existing system partition" saat install windows

I was getting this error message:

*

I went inlớn disk part and asked for disk attributes & I got that my disk had boot disk set lớn no.

How do I change this? I reset my bquả táo, và I removed all devices from the boot sequence except for my HardDrive and my USB that contains Windows 7.

Other notes: With no usb in the computer the computer complains about bootmgr missing, but this is useless because I want lớn vì chưng a clean install anyway.


windows-7 windows
Share
Improve this question
Follow
edited Jul 29 "14 at 2:35
EGHDK
asked Jul 28 "14 at 18:41
*

EGHDKEGHDK
2,35777 gold badges2222 silver badges2929 bronze badges
15
| Show 10 more comments

7 Answers 7


Active Oldest Votes
28
This sucks.

I found my solution after about another 5 wasted hours of my life.

I stumbled upon this "fix" on MS"s technet blog

I saw a comment:

I had this error on RTM with the combination of Hãng Intel 310SSD and Kingston DataTraveler Elite 3.0 USB stick.

Could it be? This particular USB stiông chồng being the issue? (I have 3 of these). I tried it on another. Same issue. Took another generic 4GB staples usb from lượt thích 5 years ago... worked fine.

Kingston. You suchồng. I don"t know why, but you vì chưng.

Side note: Put Ubuntu on the USB. Booted/installed just fine on the Kingston.


Share
Improve this answer
Follow
edited Atruyền thông quảng cáo 25 "16 at 10:29
*

Sнаđошƒаӽ
49466 silver badges1616 bronze badges
answered Jul 29 "14 at 2:35
*

EGHDKEGHDK
2,35777 gold badges2222 silver badges2929 bronze badges
8
| Show 3 more comments
18
This is the easiest solution that I found:

Remove sầu all partitions on the drive (no need lớn launch diskpart, you can just use the partition selection screen)Unplug the USB drive sầu.Click Next. You will get:Windows is unable lớn install lớn the selected location. Error: 0x80300001.Replug the USB drive sầu.Click Refresh.Clichồng Next.

Xem thêm: Giáo Án Sinh Học 6 Bài 15: Cấu Tạo Trong Của Thân Non, Giáo Án Sinh Học Lớp 6

Voila!


Share
Improve this answer
Follow
answered Sep 23 "15 at 16:04
*

AkeoAkeo dán giấy
4,31644 gold badges2121 silver badges2424 bronze badges
5
Add a phản hồi |
2
Another way, tải về e.g. a Ubuntu Desktop install image put it on a USB-drive and boot it.

Then find "gparted" và try khổng lồ use it for partitioning the drive sầu.

That might give sầu an initial partition table & partition, which may help in getting things going.

Alternative sầu with Ubuntu;

mở cửa a terminal with CTRL+Alt+T (works in at least 13.10 and 14.04).$ lsblk should display a menu of all attached disks & their partitions. USB-stuff might not appear if you have unmounted it/them (turns off power). Alternatively use gparted above and find the /dev/sdx -similar-looking name of the disk.then do

$ suvì dd if=/dev/zero of=/dev/sdx bs=512 count=1which will WIPE the first blochồng (increase count for more) of the disk, which should be the partition table.double checked the commands ;-)


Share
Improve sầu this answer
Follow
edited Jul 28 "14 at 19:22
answered Jul 28 "14 at 18:47
*

HannuHannu
7,09433 gold badges1616 silver badges3333 bronze badges
0
Add a comment |
2
Just also managed lớn spend hours fiddling with Windows 7 & a Kingston DT R3.0 G2 32GB USB3 stichồng.After picking up some cheap PNY stiông chồng everything worked like a charm.Remember having issues a while ago while trying khổng lồ put together a MacOSX 10.9 USB installer using a Kingston stick.


Share
Improve this answer
Follow
answered Nov 4 "14 at 17:36
Diông chồng VisserDiông chồng Visser
6644 bronze badges
Add a phản hồi |
1
For me it happened because I had simultaneously a portable drive sầu plugged in at another USB port. After I unplugged it it was fine.


Share
Improve sầu this answer
Follow
answered Dec 4 "15 at 22:18
xjixji
7381111 silver badges2323 bronze badges
Add a comment |
1
For me, the key parts appeared to be:

installing an MBR and bootloader on a manually created boot partition marked as active;rebooting the installer before trying to use that partition.

Here are the steps that finally took me to successful proceeding:

Create the boot (and perhaps also root) partition whatever way you prefer — such as using diskpart built-in comm& (press Shift+F10 in installer at any time, enter help or consult the documentation for the rest), or Unix tools. Be sure to allocate at least 48 MiB; around 24 MiB are user out of mặc định 100 MiB, but there should be some room left for updates. It may also be a good idea to align both partitions on 1 MiB to 16 MiB boundary depending on SSD erase block kích cỡ, if applicable.

Format the boot partition as NTFS and be sure to label it “System Reserved”. When using Unix command-line tools, one may need to manually specify 512 byte sector kích thước and 4096 byte cluster size (or 8 sectors per cluster); be also sure to check whether the partition type id in partition table is 7, which stands for NTFS and alike.

Install the master boot record and bootloader — either from a live Windows installation or from the installer itself.X:> diskpart # Run diskpart.select disk 0select partition 1active sầu # Mark partition as active.assign letter=BexitX:> bootootsect /nt60 B: /mbr # Install boot record.

Exit the installer (if running it) and reboot the machine. Simply refreshing the partition danh sách in installer will not suffice.Start the Windows installer again and select an existing root partition or create one now alongside your boot partition which should be listed as being of type “System” (rather than “Basic” for regular volumes). Upon continuing, the installer should use that boot partition automatically instead of trying to create it.

Xem thêm: U21 Việt Nam 2018 - Việt Nam Hạ Đẹp Malaysia Ở Giải U21 Quốc Tế 2018

That should lead to successfull installation. Otherwise, try other solutions.


Chuyên mục: Blogs